Safety flooring does a quiet job. In kitchens, washrooms, entrances and changing rooms, its textured surface is there so that people do not slip when the floor is wet. It is hard-wearing and made to be cleaned often. But it only does its job if it is cleaned in the way its maker intended. Clean it wrongly, and the grip can be lost without anyone noticing, either because dirt and grease fill the texture, or because a film of polish or cleaning residue sits on top. Commercial floor cleaning of safety vinyl and similar floors needs the right pad or brush, the right detergent at the right dilution, no polish or wax and proper rinsing. This guide explains why a shiny safety floor is often a dirty one, how to read the maker’s care sheet and how a contract can specify the method.
What safety flooring is
Safety vinyl has a surface that contains hard particles, such as quartz or similar grit, set into the wear layer, or a surface with a raised pattern. The particles or texture create friction, which helps shoes grip when the floor is wet or greasy. Other types of safety flooring include textured tiles, resin floors with aggregate and rubber floors with moulded patterns.
The texture is the whole point, and it is also the problem. Texture traps dirt, grease and soap residue in the small gaps between particles. A smooth floor can be mopped clean in one pass. A textured floor needs something that reaches into the surface, and when it does not, soil builds up and makes the floor look dull and feel slippery.
Why a shiny safety floor is often a dirty one
Many people clean a floor until it looks glossy. On smooth flooring, shine can mean clean. On safety flooring, it often means something else.
A safety floor is not designed to be shiny. Its surface is textured, and it looks matt or slightly textured when it is in good condition. If it looks shiny, there are usually two explanations.
- A film has built up. Grease, soap, polish or cleaning product residue has filled the texture and created a smooth layer on top. The shine is the residue, and the floor underneath has lost much of its grip.
- The surface has worn smooth. Heavy traffic, harsh cleaning or aggressive pads have worn down the texture, and the floor is no longer as slip resistant as it was.
In both cases, the floor needs attention. A floor that looks polished and feels slick under the shoe is a warning. Do not simply add more cleaner or mop harder. Find out what the floor is made of and what the maker says about cleaning it.
Read the maker’s care sheet
Every reputable manufacturer publishes care and maintenance instructions for its safety flooring. These explain the products to use, the dilution, the tools and the frequency. Ask your installer or supplier for the sheet, or find it on the manufacturer’s website. Keep a copy on site and give it to your cleaning provider.
Look for the following details.
- Which detergent is recommended, and which products to avoid.
- The dilution ratio, and whether to rinse afterwards.
- The type of pad or brush for manual and machine cleaning.
- Whether polish, wax or sealer should ever be applied.
- How often to carry out intensive cleaning.
- Whether steam, solvents or abrasive pads are allowed.
- Any advice for removing grease and stubborn soil.
If you cannot find the make of your floor, a cleaning provider can sometimes identify it, or the installer’s records may help. A general approach for unknown floors is to use a neutral or mildly alkaline detergent suited to vinyl, test in a corner and avoid polish.
The right method for commercial floor cleaning
Most safety floors respond to the same set of principles.
The right tool
A stiff brush or a suitable scrubbing pad is needed to reach into the texture. A mop alone slides over the top and leaves dirt in the gaps. For small areas, a hand brush or a deck scrubber works. For larger areas, a scrubber-dryer fitted with the recommended brush or pad cleans the surface and lifts the dirty water at the same time. Avoid pads that are too abrasive, because they wear the texture. Avoid pads that are too soft, because they do not clean it.
The right detergent at the right dilution
Use a detergent that suits the floor and the soil. In kitchens, a degreaser may be needed to cut through fat. In washrooms, a cleaner suited to soap scum may be required. Follow the dilution on the label and the maker’s sheet. A stronger mix does not clean better, and it leaves more residue, which is exactly the kind of film that reduces grip. A mix that is too weak may not shift the soil.
Dwell time
Let the detergent work. Applying it and leaving it for a few minutes before scrubbing helps it break down grease. Do not let it dry on the floor.
Rinsing
Rinse thoroughly with clean water, and remove the water with a wet vacuum or a clean mop. Rinsing removes the detergent and the dissolved soil. A floor that is not rinsed keeps a layer of residue, and the next clean adds to it. Change the rinse water often.
No polish or wax
Do not apply polish, wax or sealer to safety flooring unless the manufacturer specifically recommends it, which is rare. These products fill the texture and defeat the purpose of the floor. If a floor has been polished in the past, it may need stripping with a suitable product, following the maker’s advice, to restore the texture.
Drying
Make sure the floor is dry, or properly marked as wet, before people walk on it. A cleaned safety floor can still be slippery while damp. Use wet floor signs, work in sections and dry the entrances first.
Frequency
Daily cleaning keeps the surface from building up soil, and periodic deep cleaning removes what daily work misses. In kitchens, the floor may need cleaning at the end of every shift, with a deeper machine scrub weekly. In washrooms and changing rooms, daily cleaning and a periodic deep scrub are usual. Entrances need regular sweeping and mopping, with extra care in wet weather. The right schedule depends on use, and it should be adjusted if the floor starts to look or feel different.
Specifying the method in a contract
A cleaning contract should be specific about safety flooring. A good specification names the floor type and areas, describes the method, lists the products to be used and says how often each task is done. Include the following.
- The areas with safety flooring, and the maker’s care sheet attached.
- The tools and equipment to be used, such as the brush or pad type.
- The detergent and the dilution.
- A statement that no polish, wax or sealer will be used.
- Rinsing and drying requirements.
- The frequency of daily and deep cleaning tasks.
- How the floor is checked, and who is told if it starts to feel slick.
Exclusive Pro Cleaning describes its floor cleaning service for commercial premises on its website, and the restaurant cleaning page covers kitchens, where safety flooring is common. The commercial cleaning overview lists the other services that may be useful. Whoever you choose, give them the maker’s care sheet and ask them to confirm the method in writing.
Slip resistance information
Slip resistance is a technical subject with its own measurement methods and published guidance. The UK Slip Resistance Group is a body that works on slip resistance in the UK, and its site is a useful reference for anyone who wants to understand the field. This guide does not quote test values. If you are concerned about the slip resistance of a floor, ask a competent person to assess it, and follow the manufacturer’s guidance.
Signs the floor needs attention
- It looks glossy or greasy where it should look matt.
- It feels slick under the shoe, even when dry.
- Dirt is visible in the texture, especially in corners and walkways.
- Staff report slips or near misses.
- Cleaning products leave a film or smell.
- Cleaning takes longer than it used to, because the surface resists.
If you notice any of these, review the cleaning method, and consider a deep clean with the right tools.
Questions about cleaning safety flooring
Can I polish safety flooring to make it look better?
No, unless the maker says so. Polish fills the texture and reduces grip.
Why does my kitchen floor look shiny after cleaning?
Often because a film of grease or cleaning residue has built up. Deep cleaning with the right brush, detergent and rinse should restore the matt surface.
Do I need a machine to clean safety flooring?
Not for small areas, but a scrubber-dryer with the right brush cleans large floors more thoroughly and more consistently.
How do I know which method is right for my floor?
Check the manufacturer’s care sheet, and ask your installer or cleaning provider to confirm. To talk through a floor in your premises, contact Exclusive Pro Cleaning.
