Luxury vinyl tile, usually shortened to LVT, has become a common floor in new offices, shops and cafes. It looks like timber or stone, goes down quickly, copes with traffic and feels warmer than ceramic. It is easy to assume that something so hard-wearing needs little care. In practice, LVT is forgiving but not indestructible, and the way it is cleaned decides whether it looks good in five years or tired in two. If you look after the premises and are responsible for commercial floor care, this guide explains how LVT differs from sheet vinyl, what to use and avoid, how to control grit at the door and which scratches and scuffs can and cannot be removed.
What LVT is
LVT is made in layers. At the top is a clear wear layer that takes the traffic. Beneath it is a printed film that gives the look of wood, stone or abstract patterns. Below that is a core and backing. Tiles and planks are cut to size and fitted individually, often with a click system or adhesive. Because it is a modular floor, individual pieces can sometimes be replaced if damaged.
The wear layer is thin compared with the rest of the floor, and the thickness varies by product. That layer is what protects the pattern, so its condition matters more than anything else. Once it is scratched or worn through, the print beneath is exposed, and the damage cannot be repaired by cleaning.
How LVT differs from sheet vinyl
Sheet vinyl is laid in large rolls with few joins, and has long been the standard for hospitals, schools and shops. LVT is laid in tiles and planks, which means more joints, and it has a distinctive look. In terms of care, the differences are mostly about detail.
- Joins and edges. LVT has more seams, where water and dirt can collect. Heavy wet mopping can force water into joints, especially on floors not fully sealed.
- Finish. Many sheet vinyls were polished or sealed as part of regular care. Many LVT products are designed to be used without polish, and some manufacturers advise against it.
- Embossing. Some LVT has a textured surface that mimics wood grain. Texture traps dirt and needs a suitable brush or pad to clean.
- Appearance. A scratched LVT surface shows more because of the realistic print and the sheen of the wear layer.
Both floors are cleaned in similar ways, with neutral products and minimal water, but LVT calls for a lighter touch and closer attention to the maker’s instructions.
What to use
The general principles for cleaning LVT are simple and cautious.
Dry cleaning first
Most of the damage to LVT comes from grit. Sweep or vacuum before any wet cleaning, using a soft brush or a hard floor head, not a rotating beater bar that could scratch. Dust mopping is a good routine for large areas, and it removes grit before it can be ground into the surface.
A neutral cleaner
Use a pH neutral floor cleaner designed for vinyl, diluted as the label says. Strong alkaline and acidic products can dull the wear layer, leave a film or damage the print. Avoid ammonia, bleach and solvent-based cleaners unless the manufacturer says they are suitable.
A damp mop, not a wet one
Use a well-wrung mop, work in sections and change the water often. Excess water can seep into joints and under tiles, and on floors laid with adhesive it can weaken the bond. After mopping, allow the floor to dry, or go over it with a dry mop.
Machine scrubbing, with care
For larger areas, a scrubber-dryer fitted with a soft pad is usually suitable, with a neutral cleaner. Avoid aggressive brushes and abrasive pads, which can scuff the surface. Test a small area first and check the maker’s advice on machine use.
What to avoid
- Steam cleaners. Heat and moisture can damage the adhesive, cause tiles to lift and damage the surface. Most manufacturers advise against steam on LVT.
- Wax polish and heavy floor finish. Unless the maker recommends it, a coating can make the floor slippery, build up unevenly and cause yellowing. If a product label says it is not for polishing, believe it.
- Abrasive pads, wire wool and scouring powders. They scratch the wear layer.
- Strong solvents, such as white spirit or acetone, except as advised for specific marks.
- Rubber-backed mats that can stain. Some rubber and latex backings react with vinyl and leave permanent marks, so choose mats that are labelled as suitable for vinyl floors.
- Dragging furniture. Lift it, or use felt pads and protective glides, and take care with wheeled chairs, using suitable castors.
Grit control at entrances
Grit is the enemy. A single pair of shoes can carry stones, sand and fine particles that act like sandpaper under every footstep. The most effective protection is at the door.
- Use a matting system that is long enough to capture dirt, ideally an outer scraper mat, followed by an absorbent mat inside.
- Clean mats regularly, so that they do not become a source of dirt.
- Sweep the pavement and entrance regularly, particularly in autumn and winter.
- Keep walkways free of gravel, soil and construction debris.
- Check that mats are suited to LVT and do not have a backing that stains.
For shops and offices, good entrance matting is the cheapest way to extend the life of the floor and reduce cleaning time.
Scratches, scuffs and marks
Not every mark is the same, and it helps to know which can be treated.
Scuffs from shoes and trolleys
Rubber and heel marks often sit on the surface and can be removed with a soft cloth and a suitable cleaner, or a gentle scrub with a soft pad. These are usually removable.
Light scratches
Fine surface scratches in the wear layer cannot be buffed out like timber, and polishing them often makes them more obvious. Their appearance may improve slightly with cleaning, but they will not disappear.
Deep scratches and gouges
Damage that goes through the wear layer into the print is permanent. The remedy is usually to replace the affected tile or plank, where the floor design allows it. Ask the installer or the manufacturer about spare tiles, and keep some from the original installation.
Stains
Spills should be wiped up promptly. Ink, hair dye, strong colourants and some chemicals can stain vinyl if left. For a stubborn stain, follow the manufacturer’s advice on stain removal, and test any product on a hidden area first.
Dullness
A dull appearance may be the result of a cleaner residue or grit scratching. Rinsing thoroughly and switching to the right product sometimes restores some of the look. If the wear layer is worn, the dullness is permanent.
Manufacturer guidance
Flooring manufacturers publish care and maintenance guides, and the maker’s advice should always take priority. IVC Commercial is one of the manufacturers that describes its commercial vinyl flooring range online, and the type of information it provides is a good example of what to look for. Find the make and range of your floor, locate the care instructions and keep a copy with your maintenance records. Using non-approved products can affect any guarantee.
Fitting LVT into a commercial floor care schedule
A simple plan for most commercial LVT floors might include a daily sweep or vacuum and damp mop, a periodic machine clean with a neutral product and regular checking of matting. Exclusive Pro Cleaning describes its floor cleaning service for commercial premises, and the office cleaning and retail cleaning pages explain how floor care fits into routine services for those premises. Whoever carries out the work, give them the floor’s make and care instructions and agree the products to be used.
Planned maintenance across the year
A little planning makes LVT easier to look after. Check entrance mats every week, and replace worn ones before they stop trapping grit. Review the chairs and trolleys in the premises, and make sure wheels are suitable for hard floors, because hard or damaged castors leave scratches. Look at the floor in raking light, when low sun or a lamp shows the scuffs, and note which areas are wearing fastest. If the same lane is always worn, consider adding a runner or moving furniture to spread the load. Keep a record of the product used on the floor, the date of each periodic clean and any marks that were treated, so that a new manager or a new cleaner can pick up where the last one left off.
Spills and hazards
Wet floors are a slip risk on any hard surface, and LVT is no exception, particularly when it has a smooth finish. Wipe up spills immediately, use wet floor signs while cleaning and make sure mop water is changed regularly so that a greasy film does not build up. In kitchens and food areas, check that the floor has a suitable slip resistance rating for the use, and ask the installer if you are unsure. To ask about a schedule for an LVT floor, contact Exclusive Pro Cleaning with the floor details and your opening hours.
Questions about cleaning LVT
Can I use a steam mop on LVT?
It is usually not recommended. Steam can damage adhesive and the surface. Check the manufacturer’s guidance.
Should LVT be polished?
Only if the maker says so. Many LVT floors are designed to be used without polish.
Can scratches be removed?
Light marks on the surface may reduce with cleaning, but scratches in the wear layer are generally permanent. Deep damage may need the tile replaced.
What is the best way to protect an LVT floor?
Control grit with good entrance matting, sweep regularly and use a neutral cleaner with a damp mop.
